How To Refill A Carto Tank
Carto Tank Refilling Tutorial
https://crazyvapes.com/product/vapor-glass-tank/
Greetings vapor enthusiasts! The following demonstration is an instructional, Carto Tank refilling tutorial right here at https://crazyvapes.com/blog/ . This blog at www.crazyvapes.com descriptively explains how to refill a carto tank. When the e-liquid in your carto tank reaches, or surpasses below the cartomizer’s punched hole, then it is time to refill the tank with more e-liquid. If the punched hole on the side of the cartomizer fails to stay saturated with e-liquid, you run the risk of vaping a dry hit, or burning the coil within the carto. Once a dry hit or burn takes place, your cartomizer is usually rendered useless. The process of refilling may be new or seem tricky to many consumers, so allow me to explain the ideal method of refilling the Carto Tank.
Initially, you should utilize your trusty Carto Tank Refilling Tool. Secure the tool atop the cartomizer as if it were a Drip Tip (I prefer to have my e-cig attached for extra support). Then, while firmly holding the lower and upper Caps or Grommets securely in a grip, slowly slide the Carto Tank Refilling Tool downward, pushing the Carto away from, and underneath the upper Cap or Grommet (Ideally both Grommets or Caps should remain secure to the Tank all-the-while.) Once the Cartomizer is freed from the upper Cap or Grommet, remove the Carto Tank Refilling Tool from the Cartomizer, and remove the top Cap or Grommet (if the Grommet or Cap is difficult to remove with bare hands, use the skinny end of the Carto Tank Refilling Tool. Slide the tip of the tool into the center of the Grommet or Cap to pry it off of the Tank.) At this point, the top of the Carto should be level with the tank’s upper rim (essentially, as it was prior to this process.)
Next, simply squeeze e-liquid in the empty space between the metal Carto and inner tank… NOT inside the Carto or Filler. Refill e-liquid about 3 quarters full, allowing enough space for the Grommet or Cap to fit. Now, reattach the Carto Tank Refilling Tool on the Cartomizer again, and slide the Grommet or Cap through the tool. Then, while securing the bottom Cap or Grommet in place with your hands, assuring it won’t slide out; re-apply the upper Cap or Grommet to the top end of the tank.
An important side-note: while engaging in the refill process, periodically check for over-saturation of e-liquid within the Cartomizer Filler, or Leakage to the bottom of the tank. This may happen, but it’s not a big deal. Fix the problem by using an empty needle-nose e-liquid bottle to suck the excess e-liquid from the necessary spots. For a final touch, twist a tissue-end to a long, fine point and slide into the Vent-Chamber at the bottom of the Carto Tank. Repeat this process as needed.
At this point, both Grommets or Caps should be mostly secured to the Tank. Make a few final adjustments by flushing the top-end of the Carto with the top-end of the Cap or Grommet; make sure the two parts atop are aligned by gently pushing around the circumference. The bottom side, punched hole of the cartomizer should be no more than one or two millimeters above the lower rim of the bottom Grommet or cap.
The final step requires to double check for leaking or over-saturation; clean and mop up excess e-liquid as necessary. From this point on, your tank will be air tight until you remove the Caps or Grommets… or misalign anything by mistake (which is difficult to do).
Further Information on How to Refill a Carto Tank.
For other instructional tutorials and educational demonstrations, visit our YouTube Channel, or visit the Blog Link at www.crazyvapes.com
Have a delightful “Crazy Vapes” experience!
-Rob Close